Koncrete Tile Adhesive-200

Product Description

KONCRETE Tile Adhesive 200 is an advanced polymer enriched cement based high quality tile adhesive, best for fixing of ceramic tiles, vitrified tiles, natural stone on internal floor and wall applications. This product is also suitable for tile-on-tile application.

KONCRETE Tile Adhesive-200 is free from impurities and organic content. KONCRETE Tile Adhesive-200 is manufactured in a very stringent quality control environment and provides consistent quality with hassle free service.

This product has replaced the conventional method as it is ready to use by simple mixing with water at site and easily applying on the tiles surface. It not only gives better adhesion but also ensure the void less tiles fixing. Application of tile adhesive also ensure the time and money and also guarantees better quality tile work as compared to conventional method.

Features & Benefits

         Excellent adhesion with the substrate

         High Strength

         Self- Cured

         Better workability and durability

         Single component, Ready to use & Easy to use

         Interior application

         Extended open time

         Pre-soaking of tiles isnt required

         Anti-skid / Slip resistance

Area of Application

KONCRETE Tile Adhesive 200 is polymer modified thin bed adhesive designed for fixing of vitrified tiles, ceramic tiles and natural stone of regular size in dry application on interior floor and walls. Its also recommended to use tile on tile application. It is suitable for various cement and concrete based substrates.

Substrates

         Cement Screed

         Cement Plaster

         Concrete masonry

         Cement mortar beds

         Brick Masonry

         Cement terrazzo

         Existing ceramic tiles*

*Surface should be cleaned and roughened enough before application of tiles

Technical Table

Note

Allow a minimum of 24 hours for the subsequent usage of the areas where tilling has been done. Tiling work not suggested if ambient temperature is likely to drop below 5^oC or exceed 50^oC. For ambient temperature below 20^oC allow the adhesive to cure for an extended period of time. Pot life, open time and adjusting time depends on the surface absorption, wind factor, temperature and humidity conditions at site.

Method of Application

A)     Surface Preparation

         Prepare the surface and tiles before the application of tile adhesive by removing oil, bond inhibiting agents, dirt, dust and laitance.

         Clean the surface following suitable methods like by using wire brush, water jetting, mopping etc.

         Prior to the application of KONCRETE Tile Adhesive 200 surfaces should be leveled or repaired in case of higher undulation, KONCRETE Readymix Plaster is recommended over vertical surfaces to level it.

B)     Mixing

         KONCRETE Tiles Adhesive 200 requires 25% potable water by weight of material.

         Add KONCRETE Tiles Adhesive 200 to measured quantity of water, while continuously stirring using a mechanical stirrer for 2-3 minutes to ensure a consistency free of lumps.

         Allow the mix to stand for 2-3 minutes to mature and then mix it again before use.

         Do not add any extra water to alter the mix consistency or to extend the pot life. Further water addition will hamper the adhesion strength of the tile adhesive.

C)     Application

         Apply the mixed of KONCRETE Tiles Adhesive 200 to the prepared levelled substrate using the appropriate notched trowel according to the size of the tiles being laid.

         Its recommended to use suitable spacers while fixing of tiles to ensure uniform tile fixing and creation of joints that can be filled with epoxy tile grout later on.

         A minimum of 3 mm bed thickness of tile adhesive for wall and floors must be achieved.

         Lay tiles onto the adhesive. Gently press each tile and move it in perpendicular direction to the notches to ensure no air cavity remains in the mortar and good initial bonding is attained. Do not disturb the tiles until the adhesive has set.

         Its recommended to fix the tiles within 20-30 minutes of spreading KONCRETE Tiles Adhesive 200 to achieve adequate bonding and strength.

         Any tiles fixing after 20-30 minutes of spreading KONCRETE Tiles Adhesive 200 will lead to improper adhesion and may result in de-bonding of tiles.

         For vertical surface application, tilling should be start from bottom to top. 

Coverage

Approx 50-70* Sq.ft. per 20 Kg bag when applied by notch trowel at average thickness of 3-4 mm.

* Coverage depends upon size of notch trowel, type and size of tiles and evenness and smoothness of substrate.

Packaging

20 Kg laminated HDPE bag.

Shelf Life

Product has shelf life of 6 months from the date of manufacturing. It should be stored in cool and dry place in unopened original packing.

Precautions

         Not suitable for tilling over flexible substrates, such as fibrous cement sheeting, plasterboard and timber.

         Not suitable for tilling directly onto timber, plywood or glass.

         Not suitable for tilling directly onto metal or plastic substrates.

         Not suitable for tilling directly onto polyurethane membranes.

         Not suitable for moisture sensitive tiles or substrates.

         Try to avoid application under direct sunlight.

Safety Directions

         KONCRETE Tile Adhesive 100 is non-toxic. Use of gloves and goggles recommended. Any splashes to the skin or eyes should be washed off with clean water immediately.

        In case of prolonged irritation, medical advice should be sought. KONCRETE Tile Adhesive 100 is non-flammable.